EN 
DE 
FR 
IT 
ES 
NL Repair head gasket - permanently in just a few minutes
Steel Seal® is suitable for all engines with a closed cooling water circuit: Cars, trucks, vans, 4×4s, SUVs, motorcycles, boats, agricultural and construction machinery, etc.
Save now with the Smart repair solution from Steel Seal® many 100 euros for the exchange of the Defective cylinder head gasket.
- Easy to use
- Fast repair
- Lasting result
No tools - 99% success rate - money-back guarantee
Recommended quantity:
| Displacement | Bottles |
|---|---|
| Up to 2,400 cc | 1 |
| 2,400 cc to 4,000 cc | 2 |
| over 4,000 cc | 3 |
Where can I find my cubic capacity?
Broken head gasket repaired in 3 steps
1 - Ensure that the engine is cold. The coolant contained must be pure and water-based (recommendation: 3:1 water to antifreeze or more aqueous). Pour the recommended amount of Steel Seal® directly into the radiator or expansion tank and screw the cap back on.
2 - Set the heater and fan to the highest setting, then start the engine and let it idle until the intended operating temperature is fully reached. Allow the engine to run for a further 30 minutes while constantly monitoring the engine temperature. Switch off the engine and allow it to cool down for at least 6 hours.
3 - If necessary, top up with fresh coolant up to the specified mark on the coolant reservoir. Simply leave Steel Seal® in the cooling system and use the vehicle as usual!
* Note: If there is excess pressure in the cooling system, leave the lid open during use!
Why is it important to repair the head gasket?
The cylinder head gasket ("CCG") is an important component of the engine. It seals the cylinder head to the engine block and prevents engine oil and coolant from mixing or entering the combustion chamber. If the head gasket is damaged, this can lead to serious engine damage. A defective CCD is a serious problem and there are 7 reasons why you should not continue driving with a defective cylinder head gasket shall.
The head gasket ensures that no cooling water enters the combustion chambers of the engine. If it is damaged, it should be repaired as quickly as possible. The Removal and replacement a defective cylinder head gasket is Very time-consuming and thus a costly matter. In addition, the repair is often additional risks and follow-up costs connected. After replacing the head gasket, the cylinder head usually has to be ground flat in order to eliminate any distortion of the cylinder head.
Kühlwasserverlust und hoher Druck im Kühlsystem [VW Passat 3 BG, 1.9 tdi, Bj. 2002]
Motorlauf unregelmässig, weisser Qualm durchgehend, Temperatur nach kurzer Fahrt im roten Bereich [Toyota Avensis BJ 2005, 2.0 Benziner]
How can you recognize a defective cylinder head gasket on the oil cap?
Checking the cylinder head gasket - how it works
Druck im Kühlsystem – Ursachen, Anzeichen und Lösungen
Oil in the coolant - causes, signs and what you can do
Repair a defective head gasket yourself at low cost?
However, repairing the head gasket does not have to be a complicated or labor-intensive process as long as the engine still starts and runs for 60 minutes without overheating. Because with Steel Seal® there is a favorable and since 1999 Proven alternative for replacing the cylinder-head gasket in the workshop. Steel Seal® with its 3-fold patent is a specially developed repair solution for leaking cylinder-head gaskets in the early stages. The product is simple and permanent effective. Here you will find all the important Tips for using Steel Seal®.
But don't trust us "blindly", instead find out more from one of the over 300 Steel Seal® specialist dealers in German-speaking countries that proudly stock Steel Seal® and offer this product to their customers with complete conviction.
Head gasket repaired or money back
Of course, in some cases the damage to the defective head gasket may be too advanced for repair with Steel Seal®. As no repair solution of this type has a 100% success rate, we cannot seriously promise that Steel Seal® will repair the existing head gasket damage.
Nevertheless, there is no product with a higher success rate in permanently repairing a leaky Cylinder head gasketas long as the Engine still starts and the problem in time is being tackled, there are indeed
It is unlikely that Steel Seal® will fail when used properly. Should this nevertheless happen, we will be happy to reimburse you within the scope of our advertised Money-back guarantee We will either refund the purchase price or supply a replacement product free of charge.
If you have any technical questions about how best to prepare and use the product, contact our free product support team today!
Service times: Mon-Fri from 9:00 - 16:00 | Tel: +49-9101-9018160 or +43-1-9962116 | E-mail to info@steelseal.de
